Most laptop batteries last 18-24 months with average use. This is equivalent to 500-800 charging cycles. Average use of a battery will eventually drain the battery’s ability to hold a charge or there may be some adjustments that you can make to get better performance from your battery. However, if your battery is old and is getting less than half of it’s original run-time, then it may be time for a new battery. If you use your lenovo battery everyday, use it for gaming, video streaming and are on WiFi constantly, the laptop will drain the battery run-time and over all life much quicker. Such heavy use can render the battery dead in as little as one year with heavy laptop use. Get maximum performance from your laptop battery by following a few suggestions below:
Condition New Batteries
New laptop batteries come in a discharged condition and must be fully charged before use. It is recommended that you fully charge the battery to 100% and let the thinkpad t40 battery discharge completely on its own. Repeat this procedure 3-4 times to break in the battery and so each battery cell can reach it’s full charging potential. Then condition or exercise the battery at least once a month. Li-Ion battery need only be drained to about 40%, not a full discharge for monthly maintenance, however constant shallow charges should still be avoided. Sometimes it’s not conditioning that the thinkpad t40 battery needs, but a battery recalibration. Constant shallow charging will confuse the battery and it may need to be re-calibrated. For more information on how to recalibrate your battery visit this link. BIOS Says to Recalibrate My Laptop Battery.
Don’t Mix Chargers & AC/DC Adapters
Not all laptops of the same brand use the same type of charger/adapter. Do not assume that the same charger your friend uses on his Toshiba will be the correct one for you model of lenovo. Every laptop requires it’s own specific specs and both the in and out source specifications Amps and Volts must be correct for your laptop model and thinkpad t41 battery chemistry. Mixing or using the wrong charger can damage the battery and the laptop. You may not notice any difference at first, but the laptop or battery may show signs of a problems later. Do not use a swollen battery. Carefully remove and contact a local recycle center or repair shop for advice on discarding the thinkpad t41 battery.
Reduce or Set Your Laptop to Battery Saver Mode
Most laptops allow you to adjust the settings to thinkpad t42 battery saver mode. Turning down the monitor brightness and turning off programs running in the background will also help in reducing drain on the battery. Remember that WiFi, Gaming and Video Streaming eats up a lot of battery power. We recommend using the AC/DC adapter when you can if on WiFi, Gaming and Streaming Video.
Avoid Memory Effect
Keep your thinkpad t42 battery healthy by fully charging and then fully discharging it at least once a month. Li-Ion batteries do not suffer from the memory effect, but they too still need conditioning at least once a month with a discharge to about 40% and should not be overcharged.
Remove Battery when Using AC/DC Power Source
Laptop batteries are in constant charge and discharge state when you have the AC/DC adapter plugged into the computer and using the computer with the thinkpad t42 battery installed. Removing the battery while using the AC/DC adapter will help prolong the life span of the battery since most last 500-800 charging cycles or 18-24 months. These frequent shallow charges do not allow all of the battery cells to properly condition for optimum battery performance.
Keep your Batteries Clean
Cleaning dirty thinkpad t43 battery contacts with a cotton swab and alcohol will help maintain good connections between the battery and the electronic device.
Exercise the Battery
Condition the battery at least once a month. If your thinkpad t43 battery has not been used for a long period of time, perform the new battery break in procedure described above (condition).
Laptop Battery Storage
NiCad, NiMH and Li-Ion batteries self-discharge during storage Batteries need to be broken in before use. If you don’t plan on using the battery for at least a month or more, the battery should be stored in a cool dry place. Do not leave the lenovo battery inserted in the laptop for long periods of time with the AC/DC adapter plugged in constantly charging the battery. Not only will this reduce the battery’s life, it can over charge the battery and damage the laptop.
Tags: lenovo battery, thinkpad t40 battery, thinkpad t41 battery, thinkpad t42 battery, thinkpad t43 battery
Trackback
•
Posted in battery news
China’s lithium-ion battery standard
China’s current Laptop battery safety standards for lithium-ion batteries contain safety requirements or product specifications are as follows:
1.GB/T18287-2000 “cell phone use lithium-ion battery general norms”; 2.GB/T19521.11-2005 “Li-ion battery pack hazardous properties of dangerous goods inspection and safety standards” 3.GB/Z18333.1-2001 “Electric road vehicles lithium-ion batteries “; 4.YD1268.1-2003″ mobile phones and lithium battery safety requirements and test methods “; 5.SJ/T11169-1998″ Lithium Battery Standard “(eqvUL1642: 1995); 6. QB/T2502-2000 “general standards for lithium ion nikon d40X vertical-grip“; 7.QC/T743-2006 “electric vehicles using lithium-ion batteries”; 8.SN/T1414.3-2004 “import and export of battery safety test methods Part 3: Lithium ion batteries. ”
The above criteria, the first three as the national standard, the former two for a recommended national standard, but GB/T19521.11 Chapter 4 and Chapter 5 for the mandatory elements, the third criterion for the guidance of technical documents; after 5 respectively, post and telecommunications, electronics, light industry, automobile, commodity inspection industry nikon d60 vertical-grip standards, post and telecommunications industry standards YD1268.1 mandatory standard, the other four are recommended standards.
Electronics industry standard SJ/T11169 the technical content of the 1995 edition with the UL1642 standard equivalent.
Currently awaiting approval issued safety standards for lithium-ion nikon d80 vertical-grip contain safety requirements or product specifications are:
1.GB / T ××××- 200 × / IEC62133: 2002 “containing alkaline or other non-acid batteries and battery electrolytes – Portable sealed batteries and battery safety requirements”; 2.GB/T18287-200 × “mobile phone use lithium-ion fujitsu lifebook c2320 battery and battery universal norms”; 3.SJ / T × × × -200 × “mobile power systems for portable computers General Specification.”
The first two national standard, the third for the electronics industry standard, all three are recommended standards. The first is applicable to all types of alkaline batteries for portable applications, including lithium-ion battery; the second revised version of standards GB/T18287-2000 standards for lithium-ion fujitsu lifebook c2330 battery for mobile phones; third standard applies notebook computer lithium-ion batteries.
Tags: battery, blog, business, internet, laptop, life, news, notebook, replacement, world
Safety standards in three areas
Recently, the Laptop battery Ministry of Information Industry set up the Electronic Product Safety Standards Working Group to prepare to carry out the work safety standards for lithium-ion batteries, and put forward to develop safety standards for lithium-ion batteries for portable work objectives, combined with the status quo of China’s standards for lithium-ion batteries, the proposed safety standards for the future carry out the work of the following several measures in order to obtain greater effectiveness.
1. To national standards in the form of a unified nation-wide safety standards for lithium-ion canon eos 500d vertical-grip.
Lithium-ion battery as a ubiquitous product, unified its safety standards are not only fully protect the interests of consumers needs, but also reduce the cost of doing business, standardize the industry development requirements. Taking into account the lithium-ion battery production, marketing and other areas across the national economy, a unified security standard form should no doubt be the highest level of national standards. In order to maintain safety standards and that the unity should take the following measures: on the existing state and industry standards, they should be integrated canon eos 1000d vertical-grip technical content to include or an alternative manner; in the future with the development of lithium-ion battery, through the standard way of amendments to update their safety requirements will no longer be the development of other safety standards.
2. According to the product of lithium-ion battery standard, the standard level of adherence to the “moderate” principle.
Fur products and standards are inter-relationship between the different nature of the product accordingly, requires different standards, the current lithium-ion battery roughly divided into two major fujitsu lifebook c2240 battery energy-and power-type products, two products in materials, design structure, etc. There is a certain the differences in the same security context, as well as its standard test method requirements are likely to be different.
Commonly referred to as belonging to the former category of portable battery products, including mobile phones, laptop computers, digital cameras and video cameras use lithium-ion batteries, electric tools, electric bicycles and electric vehicles using lithium-ion battery products grouped into the latter category, the proposed difference to develop fujitsu p250 battery safety standards for lithium-ion batteries for portable and power-based lithium-ion battery safety standards.
Standards should be appropriate means to seek and establish product safety and performance of the best combination, if it is not simply focus on safety, of course, the more stringent requirements as possible, but the overall technical level of the product restrictions, the better the security often means more poor electrical performance level, a typical example is the current charge GB/T18287-2000 the 3C to 10V over-voltage charging requirements, unless the significant expense of capacity or life, or the current lithium-ion batteries used in mobile phones simply can not achieve this has been does not prove the necessary safety requirements. From the application point of view, it is obviously not worth the candle, and do not meet the standard within a certain range to create a basic principle of the best products.
3. To enact a specific safety standards for lithium-ion fujitsu fpcbp65 , fujitsu fpcbp65ap batteries, the standard covering the product design and manufacturing processes, and establish the appropriate oversight authentication mechanisms.
Lithium-ion battery safety standards and product specifications should be separated from the development, its benefits are standard in a more flexible way to fit the needs of product development. In the widely used under the facilitation of the electrical properties of lithium-ion battery upgrade is almost with each passing day, compared to its security requirements is relatively fixed, respectively, standard-setting will enable the two to move in the form of sub-objects to meet the changing needs of their own, so as to avoid in the past all of the requirements of product standards of the general canonical form of the shortcomings of time-consuming fujitsu lifebook c2000 battery amendments.
The vast majority of the safety of lithium-ion battery is difficult to simulate from the current safety standards, the internal short circuit caused by defects, only the lithium-ion fujitsu lifebook c2310 battery design and manufacturing process quality control system fully integrated into the product of internal short circuit can only effectively eliminate the risk, and it in the industrial sector in a large number of security incidents lithium-ion batteries are summarized and reached consensus. Therefore, improving the structure of existing safety standards, will expand its content to the upstream product design and production processes are fully and effectively to protect the safety of lithium-ion batteries needed. This, in turn has brought the standard implementation of operational problems, the proposed new forms of standards based on lithium-ion batteries to carry out mandatory safety certification, in addition to testing the final product, the authentication methods should also include product design and process review, supervision of the manufacturing process content and reference to quality system certification practices, establish a regular review and random sampling of the system, so will ensure that the maximum nikon d40 vertical-grip could be carried through standard content and implementation.
Tags: battery, blog, business, internet, laptop, life, news, notebook, replacement, world
Solid State Circuit Conference, imec and Holst Centre report a 2.4GHz/915MHz wake-up receiver which consumes only 51µW power. This record low power achievement opens the door to battery-less or energy-harvesting based radios for a wide range of applications including long-range RFID and wireless sensor nodes for logistics, smart buildings, healthcare etc.The development is faster than laptop batteries(thinkpad t40 battery,thinkpad t41 battery)
Today’s battery-operated wireless communication systems consume a lot of power at times when the radio does not have to transmit or receive data. This means that most of their time Bluetooth or WLAN radios on mobile phones are taking energy from the battery without adding functionality. Imec and Holst Centre’s wake-up receiver with ultra-low power consumption and fast response time can be put in parallel with the conventional radio to switch it on when data needs to received or transmitted.thinkpad t40 battery,good laptop batteries.
Imec and Holst Centre developed an innovative radio architecture based on double sampling to overcome the 1/f noise problem. This noise affects most low data rate (10-100kbps) radios. As a consequence, these radios traditionally have a higher power budget than higher data rate radios achieving the same performance. By using a double-sampling technique the offset and 1/f noise is reduced and consequently the sensitivity of the receiver improves proportionally as data-rate scales.
The wake-up receiver chip was implemented in a 90nm digital CMOS technology and occupies an area of 0.36mm2. Measurements on silicon show a sensitivity of -75dBm (SNR>12dB) for the 915MHz receiver at 100kbps OOK (on off keying) modulation. When scaling the data rate to 10kbps and filtering the out-of-band noise, the sensitivity is improved by 5dB. For the 2.4GHz receiver, the sensitivity is -64dBm and -69dBm for 100kbps and 10kbps data rate respectively.
“Within our wireless autonomous sensor system research, we aim to develop wireless sensor systems powered by energy harvested from the environment instead of using batteries.(thinkpad t41 battery,thinkpad t42 battery) The power budget of such systems is only 100µW for the DSP, radio and sensor. This ultra-low power radio of only 51µW with small form factor is a major step forward to achieve our goal. It opens the door to many new battery-less applications such as long-range RFID, smart lighting, and sensor tags.” said Bert Gyselinckx, general manager imec the Netherlands at Holst Centre.
Tags: thinkpad t40 battery, thinkpad t41 battery, thinkpad t42 battery
Trackback
•
Posted in battery news
First of all, repeatedly charging and discharging has basically no damage to Nikon en-el3 battery due to more active lithium element and no memory effect, so with the manufacture of lithium batteries can be repeated charge and discharge. We are now big Most people (90% or more) way of thinking is also retained in a few years ago the popular shadow of nickel-metal hydride batteries, because the nickel element in itself is not active, and the element has a memory of electronic effects, namely: remember the last red depth of discharge! So, if it is not charging the laptop battery runs out or the long (fully stimulate the nickel element – its not active), the charge can not achieve the best results, it is generally charge their time at night or how many hours!
We are now using a lithium element, the element can not exist independently in nature can only exist in the compounds, in the periodic table, the lithium half-life is very short, and no memory effect, so the process of lithium Nikon en-el8 batteries in use electrical impulse can not be a long and full discharge, owing to the charge make their own very active element in the electronic state of saturation occurs strenuous exercise, while production of explosive mix, namely: charge time is best for the 2-4 hours, preferably not more than 4 hours (more active elements, charge to stimulate fast akku charging time is correspondingly shorter, even the first charge is only 2 hours to 4 hours, due to lithium has no active elements, and Instead, on the impact of lithium long charging elements in the process of charging and discharging the level of activity).
Followed by lithium battery charging process, we will find the Casio np-100 battery is full at least at this time like one half an hour in charging process, because firstly voltage impulse charging is completed, then the electronic charge is finished slowly about half an hour! When electricity is best not to completely run out of recharge, because ran out of lithium element required by the needs of the reverse reaction of compounds not have enough fully charged, resulting in cell capacitance decreases!
So to sum up, cell phone lithium battery for Jvc bn-vf808 is the modern invention of the humanization of the batteries, it is, and notebook computers \ MP3 and other electronic products, batteries are the same, basically do not bother charging and discharging
- Charging time 2-4 hours (not too long, a long time would seriously affect the Fujifilm np-120 battery life and dangerous)
- The first charge can not for a long time, and usually charge the same as you can (and do not enter the nickel-metal hydride batteries Mistakes)
- Can not be entirely optical (fully depleted, the battery life also have serious impact)
A lithium Casio np-30 battery can deeply discharge cycles for a few times, more very bad 4. The use of the process, see the fast there was no electricity, and perception of not enough of the red, will be full of the best, it does not matter washed dissatisfied !
Plastic Solar Cells
Solar energy has become Dell Inspiron 1526 Battery widely recognized throughout the world of clean energy, but also how to improve the efficiency of its approach by which to reduce the cost of solar cells have become a topic of wide discussion, and now our neighbors South Korea on a new breakthrough in this regard .
Not long ago, South Korean researchers have used the principles of plant photosynthesis, have developed a plastic as the material to solar cells, batteries cost far less than the ordinary solar cells. At present, this plastic solar cells, photovoltaic energy conversion rate has reached 6.5%, nearly 7% of the commercial standard. Since the Dell Inspiron 1720 Battery of plastic as the main material, so the use of polysilicon as the material costs than the ordinary solar cells is much lower.
Moreover, unlike in the past can only absorb visible light in sunlight the solar cell is different because it uses two overlapping laminated solar cell structure, and this addition to the battery can absorb visible light, but also can absorb near-infrared, which greatly improved of solar Dell Inspiron 6400 Battery energy utilization. Thereby reducing the cost basis to achieve efficiency improvements.
The new technology can reduce the amount of platinum in photovoltaic cells
Israeli scientists have developed a new technology Dell Latitude D420 Battery for battery in the platinum nano-particles can be solar energy into electricity, thus reducing the production of photovoltaic cells use platinum, which means the cost of solar panels will be reduced.
Israel Bar-Ilan University, Nanotechnology Research Institute, Professor Arie Zaban said the cost of solar technology an important factor in the successful application in order to obtain widespread use, solar cells must be less than the cost of the use of natural energy and produce electricity.
The use of platinum nanoparticles can reduce the amount of apple A1175 , apple A1185 platinum and therefore significantly reduce the cost of solar energy production.
Tags: blog, business, game, internet, interview, life, news, Plastic Solar Cells, tips
Delkin new patent batteries
United States manufacturer sony np-fa70 battery of advanced digital equipment, Delkin (del DRC) has introduced three patented technologies add AA batteries, and said the new battery is more for professional photographers demand. With the new patented battery technology, was named Delkin Power series, the new battery storage capacity increased significantly, can bring a lot of benefits for photographers. The new product line includes 2900mAh rechargeable battery, plus AA / AAA charger and sony np-fa50 battery, also provides a disposable alkaline batteries.
Delkin Power Series Battery
All Delkin Power product warranty period of two years, IWS, as detailed in the company’s Web site http://www.ecsem.net. Including charger including 4 AA rechargeable batteries for 44.99 U.S. dollars. Delkin Devices is one of the top California high-end digital cameras sony np-f970 battery, storage equipment and accessories manufacturer, located in San Diego, California.
Japanese invent a new automotive fuel-cell technology
September 14, Japan’s Daihatsu Motor Co. in Tokyo, showing the staff of the new sony np-f750 battery automotive fuel cell model.
This fuel cell uses a liquid used to make rocket fuel hydrazine hydrate as fuel and power output effects can be comparable to hydrogen fuel cells, improving the traditional use of methanol fuel cells and other liquid fuels arising from the problem of insufficient power sony np-f730 battery output.
Tags: blog, business, game, internet, interview, life, news, tips
Light Funnel
Latest Discovery HP Battery and Innovation: “Light Funnel” generating Apple Battery capacity than conventional silicon cells increased 3-4 times
Several times to track the new concentrator photovoltaic systems have been known as the Nobel laureate Lee is “the perfect combination of theory and practice of China’s environmental protection cause and the use of new energy sources will have a profound impact.” News today from the Ordos City, Inner Mongolia Autonomous Region Development and Reform Commission was informed that the introduction of the system construction of 205 kilowatts desert demonstration power plant end of this month will be fully grid with compaq presario x1000 battery.
With the widely used flat compared to a fixed PV systems, with the same amount of silicon cells, the actual output power can be increased 3-4 times, so that our country is expected to rely on new technologies with independent intellectual property rights to address the high cost apple a1021 of solar power disruption The worldwide problem.
Two years ago, was the University of Cambridge Corpus Christi College Senior Fellow, is currently professor of China University of Technology Dr. Chen Yingtian home should be days of Anhui New Energy Co., Ltd. to jointly develop a new multiple condenser tracking photovoltaic apple a1036 power generation system, two prototype has been in the Institute of Theoretical Physics, stable and reliable operation, etc. for over a year. The system is also installed on the roof of the Shanghai World Expo.
Reporters on the demonstration power plant to see, from octahedral reflector surrounded condenser or “light funnel” and the ordinary photovoltaic cells constitute a discrete unit of electricity. Smooth and slick as the diamond-like funnel of light in the sun shine. According to reports, this new condenser surface and the tracking method can be more effective to accept solar energy, even if it is cloudy, cell fixation can also be achieved according to set procedures for accurately tracking the movement of the sun with apple A1078 , apple A1079. Compared with the conventional tracking mode, the new device greatly improved the reliability and accuracy, and more suitable for field application.
June 8 this year, to begin the comparative experiment showed that the new multiple concentrating photovoltaic power generation system to track the average power generation volume is flat with an area of 2.5-4 times the fixed cells can be reduced by 70%% At this high energy consumption, high pollution of the apple A1148 silicon cells use. According to reports, demonstration power plant electricity price will be at 3 yuan / kilowatt-hour or so, an ordinary flat-panel technology, cost of power generation 50%%.
Tags: blog, business, game, internet, interview, life, Light Funnel, news, tips
Subject collision pacemaker cell
This unique pattern formed by the nano- compaq presario b1200 battery invention is the result of collisions of many different disciplines need materials science, energy storage, and chemistry expertise. In addition to Linhardt, the paper’s authors also include materials science and engineering Pulickel M. Ajayan, Professor and engage in chemical research, Professor Omkaram Nalamasu.
The researchers used ionic liquid, essentially a liquid salt, as the battery electrolyte. It is noteworthy that the ionic liquid does not contain water, which means that there is no such cells can be frozen or evaporated material. No water in this material, which makes the paper energy storage device can in compaq presario m2000 battery extreme temperature conditions work properly.
In addition can be used in a lot of small-scale hand-held electrical devices, the paper batteries extremely light weight makes these cells into the vehicle, aircraft or ships an ideal choice. It can also be made into different shapes, such as car doors, which is likely to raise a number compaq presario r3000 battery of important new engineering invention. Shaijumon professor added: "Since the vast majority of cell components of paper, so it is also environmentally friendly."
At the same time paper also has a high biocompatibility, so this new pattern the battery / super capacitor with a mixture of implantable devices as a power supply potential. The research team did not add electrolytes to produce the paper battery, and a testament to human sweat, blood and urine of naturally occurring electrolytes can be used to activate the battery. Pushparaj says: "so that you can use such a cell as a small-scale devices like pacemakers such power, while not yet common household compaq presario v2000 battery will be those harmful chemical substances into the human body."
Create the paper batteries are inexpensive materials, but now the team have not yet found a cheap, mass production of the device can approach. Their ultimate goal is to be able, as the printing press to produce a roll as a roll.
Professor Ajayan said: "When we overcome this technology, we basically have the compaq presario v4000 battery ability to print batteries and super capacitors of. We believe that this technology is the current energy market, as well as the electronics industry needs, people are always constantly the pursuit of smaller, lighter power supply. What we in this paper batteries can be applied to any kind of electrical appliances. "
The research team has applied for patent protection for the invention. At present they are committed to advancing the efficiency of the device compaq presario v5000 battery, and to explore different production technologies.
Tags: blog, business, game, internet, interview, life, news, tips
- Nickel-cadmium batteries (Ni-Cd)
- Nickel-metal hydride batteries (Ni-MH)
- Li-ion battery
- Fuel Cell (Fuel Cell)
It is used in laptop batteries for Sony np-fa50 in the veteran, but because it has a serious memory effect as well as the anode material used in nickel (Ni) on the environment will be toxic and cause pollution, so it is quickly was despise laptop, and replaced by a more superior nickel-metal hydride batteries.
the structural principle of nickel-metal hydride Sony np-f750 batteries is same with nickel-cadmium batteries , but it replaced the cathode by performance better, more environmentally friendly non-toxic nickel – metal hydride materials. Although only a small change, but it has brought a dramatic increase in performance. It also has an unmatched to make the advantages of nickel-cadmium battery is memory effect was not obvious, so that so that we no longer have the memory effect for that nasty trouble and become more user-friendly. Although the performance of nickel-metal hydride batteries for Sony np-fa70 are very good, but with technological advances, it is lighter in weight and a higher energy density lithium batteries replaced, become the laptop battery in the history of deadwood.
Many people think that lithium Sony np-fc11 battery means that we are now commonly used in lithium-polymer battery, in fact, lithium batteries, including lithium metal-ion battery (Li-MO2) and lithium-polymer battery (Li-ion) are two. Because Li-MO2 cells to enter the market in 1989, caught fire when the explosion occurred while the die, so it will soon disappear from people’s sight, replaced by a safer lithium-polymer battery. It is light weight, in the same capacity under its nickel-metal hydride battery for Sony np-ff50 weighs only about 1 / 2, so it is fast becoming the new darling of mobile portable devices have been used in most notebook computers, is now the backbone of notebook batteries.
Fuel cells are the future of laptop battery star, it has many types, including proton exchange membrane fuel cell (PEM), alkaline fuel cell (AFC) and solid oxide fuel cell (SOFC) and many other However, due to the fuel cell start-up time and operating temperature and other reasons in fact suitable for notebook computer use only the fuel cell proton exchange membrane fuel cell (PEM). PEM fuel cells for Sony np-ff70 using methanol fuel, from the positive and negative electrodes composed of the principle of its power generation is the result of the methanol, after re-enter the negative hydrogen and oxygen enter the cathode, through the catalyst, hydrogen atoms into protons and electrons, by different paths into the cathode, e-cycle to produce electricity through an internal, proton through the electrolyte to achieve positive, combined with oxygen to produce water and electrical and heat.
The experts agreed that restricting the commercial application of fuel cells, the biggest factor is the fuel Sony np-fh70 cell to use the metal platinum (Pt) or platinum as catalyst to make the cost of production has been high, the current production cost of the fuel cell 500 ~ 1000 USD / kW. Research shows that only when the fuel cell production costs fell to 50 U.S.dollars / kilowatt level can be truly accepted by consumers. The high cost of fuel cells is mainly due to mass production has not been formed, once entered mass production stage, the price of fuel akku will certainly be greatly reduced.
To know more,please click: flixya soulcast blurty livejournal xanga desiblogz.com/
0